Fix switching from EAP-SIM to EAP-AKA/AKA'

Switching EAP method from EAP-SIM to EAP-AKA fails.
wpa_cli commands are below.

------------------
sudo wpa_cli add_network
sudo wpa_cli set_network 0 ssid '"eap-sim"'
sudo wpa_cli set_network 0 key_mgmt WPA-EAP
sudo wpa_cli set_network 0 eap SIM
sudo wpa_cli set_network 0 pin '"1234"'
sudo wpa_cli set_network 0 pcsc '""'
sudo wpa_cli select_network 0

sudo wpa_cli disable_network 0
sudo wpa_cli disconnect
sudo wpa_cli remove_network 0

sudo wpa_cli add_network
sudo wpa_cli set_network 0 ssid '"eap-sim"'
sudo wpa_cli set_network 0 key_mgmt WPA-EAP
sudo wpa_cli set_network 0 eap AKA
sudo wpa_cli set_network 0 pin '"1234"'
sudo wpa_cli set_network 0 pcsc '""'
sudo wpa_cli select_network 0
------------------

Then EAP-AKA connection resulted in fail.
wpa_supplicant log is below.

------------------
wlan0: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 23 (AKA) selected
SCARD: Non-USIM card - cannot do UMTS auth
EAP-AKA: UMTS authentication failed (AUTN)
wlan0: CTRL-EVENT-EAP-FAILURE EAP authentication failed
------------------

This occurs because on the first EAP-SIM authentication, the SIM/USIM
card in the device was recognized as SIM card even if it is USIM card.

So this patch changes it to recognize as USIM card even if EAP-SIM
authentication was required.

I have tested these switching cases.
EAP-SIM -> EAP-AKA
EAP-SIM -> EAP-AKA'
EAP-AKA -> EAP-SIM
EAP-AKA -> EAP-AKA'
EAP-AKA' -> EAP-SIM
EAP-AKA' -> EAP-AKA

Signed-hostap: Masashi Honma <masashi.honma@gmail.com>

wpa_supplicant/events.c

@@ -273,7 +273,7 @@ int wpa_supplicant_scard_init(struct wpa_supplicant *wpa_s,
 {
 #ifdef IEEE8021X_EAPOL
 #ifdef PCSC_FUNCS
-	int aka = 0, sim = 0, type;
+	int aka = 0, sim = 0;
 
 	if (ssid->eap.pcsc == NULL || wpa_s->scard != NULL)
 		return 0;
@@ -312,14 +312,9 @@ int wpa_supplicant_scard_init(struct wpa_supplicant *wpa_s,
 
 	wpa_dbg(wpa_s, MSG_DEBUG, "Selected network is configured to use SIM "
 		"(sim=%d aka=%d) - initialize PCSC", sim, aka);
-	if (sim && aka)
-		type = SCARD_TRY_BOTH;
-	else if (aka)
-		type = SCARD_USIM_ONLY;
-	else
-		type = SCARD_GSM_SIM_ONLY;
 
-	wpa_s->scard = scard_init(type, NULL);
+	wpa_s->scard = scard_init((!sim && aka) ? SCARD_USIM_ONLY :
+				  SCARD_TRY_BOTH, NULL);
 	if (wpa_s->scard == NULL) {
 		wpa_msg(wpa_s, MSG_WARNING, "Failed to initialize SIM "
 			"(pcsc-lite)");