| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475 |
- From c6e2b7dad39a7887f935458d1c8de84db06243e1 Mon Sep 17 00:00:00 2001
- From: Chen-Yu Tsai <wens@csie.org>
- Date: Thu, 26 Dec 2013 17:15:47 +0800
- Subject: [PATCH] ARM: dts: sun7i: add bluetooth module to CubieTruck DTS
- The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The
- Bluetooth part is a BCM20710 IC connected to UART2 in the A20
- SoC. The IC also takes a 32.768 KHz low power clock input, a power
- enable signal and a wake signal via GPIO.
- The Bluetooth module supports out-of-band interrupt signaling via
- GPIO, but this is not supported in this patch.
- ---
- arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 36 ++++++++++++++++++++++++++++++
- 1 file changed, 36 insertions(+)
- --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
- +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
- @@ -88,6 +88,20 @@
- interrupts = <10 8>; /* PH10 / EINT10 */
- interrupt-names = "host-wake";
- };
- +
- + bt_pwr_pin: bt_pwr_pin@0 {
- + allwinner,pins = "PH18";
- + allwinner,function = "gpio_out";
- + allwinner,drive = <0>;
- + allwinner,pull = <0>;
- + };
- +
- + bt_wake_pin: bt_wake_pin@0 {
- + allwinner,pins = "PH24";
- + allwinner,function = "gpio_out";
- + allwinner,drive = <0>;
- + allwinner,pull = <0>;
- + };
- };
-
- usbphy: phy@01c13400 {
- @@ -171,6 +185,12 @@
- status = "okay";
- };
-
- + uart2: serial@01c28800 {
- + pinctrl-names = "default";
- + pinctrl-0 = <&uart2_pins_a>;
- + status = "okay";
- + };
- +
- i2c0: i2c@01c2ac00 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- @@ -264,6 +284,22 @@
- enable-active-high;
- gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>;
- };
- +
- + rfkill-switches {
- + compatible = "simple-bus";
- + pinctrl-names = "default";
- +
- + rfkill_bt {
- + compatible = "rfkill-gpio";
- + pinctrl-0 = <&bt_pwr_pin>, <&clk_out_a_pins_a>;
- + rfkill-name = "bt";
- + rfkill-type = <2>;
- + bt_shutdown-gpios = <0>, <&pio 7 18 0>; /* PH18 */
- + bt_reset-gpios = <&pio 7 24 0>; /* PH24 */
- + clocks = <&clk_out_a>;
- + clock-frequency = <32768>;
- + };
- + };
- };
-
- #include "axp209.dtsi"
|
