openwrt_chaos_calmer/target/linux/ramips/dts/WZR-AGL300NH.dts

/dts-v1/;

/include/ "rt2880.dtsi"

/ {
	#address-cells = <1>;
	#size-cells = <1>;
	compatible = "WZR-AGL300NH", "ralink,rt2880-soc";
	model = "Buffalo WZR-AGL300NH";

	palmbus@300000 {
		gpio0: gpio@600 {
			status = "okay";
		};
	};

	pinctrl {
		state_default: pinctrl0 {
			gpio {
				ralink,group = "i2c", "uartlite", "mdio";
				ralink,function = "gpio";
			};
		};
	};

	cfi@1f000000 {
		compatible = "cfi-flash";
		reg = <0x1f000000 0x800000>;

		bank-width = <2>;
		device-width = <2>;
		#address-cells = <1>;
		#size-cells = <1>;

		partition@0 {
			label = "uboot";
			reg = <0x0 0x30000>;
			read-only;
		};
		partition@30000 {
			label = "uboot-env";
			reg = <0x30000 0x10000>;
			read-only;
		};
		factory: partition@40000 {
			label = "factory";
			reg = <0x40000 0x10000>;
			read-only;
		};
		partition@50000 {
			label = "firmware";
			reg = <0x50000 0x3b0000>;
		};
	};

	ethernet@400000 {
		status = "okay";
		mtd-mac-address = <&factory 0x4>;

                port@0 {
			ralink,fixed-link = <1000 1 1 1>;
		};

		mdio-bus {
			status = "okay";
			phy0: ethernet-phy@0 {
				phy-mode = "mii";
				reg = <0>;
			};
		};
	};

	rtl8366s {
		compatible = "realtek,rtl8366s";
		gpio-sda = <&gpio0 1 0>;
		gpio-sck = <&gpio0 2 0>;
	};

	wmac@480000 {
		ralink,mtd-eeprom = <&factory 0>;
	};

	gpio-keys-polled {
		compatible = "gpio-keys-polled";
		#address-cells = <1>;
		#size-cells = <0>;
		poll-interval = <100>;
		wps {
			label = "wps";
			gpios = <&gpio0 0 1>;
			linux,code = <0x211>;
		};
		router {
			label = "router_switch";
			gpios = <&gpio0 7 0>;
			linux,code = <0x100>;
		};
		reset {
			label = "reset";
			gpios = <&gpio0 9 1>;
			linux,code = <0x198>;
		};
	};

	gpio-leds {
		compatible = "gpio-leds";

		router {
			label = "buffalo:green:router";
			gpios = <&gpio0 8 1>;
		};
		diag {
			label = "buffalo:red:diag";
			gpios = <&gpio0 12 1>;
		};
		security_g {
			label = "buffalo:orange:security_g";
			gpios = <&gpio0 11 1>;
		};
		security_n {
			label = "buffalo:orange:security_n";
			gpios = <&gpio0 13 1>;
		};
	};


	pcibus0: pci@00440000 {
		compatible = "ralink,rt288x-pci";
		reg = <0x00440000 0x20000>;
		#address-cells = <1>;
		#size-cells = <1>;

		status = "ok";
	};
};