| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293 |
- --- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
- +++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
- @@ -716,6 +716,27 @@ static struct board_info __initdata boar
- .ext_irq = 2,
- },
- };
- +
- +static struct board_info __initdata board_V2500V_BB = {
- + .name = "V2500V_BB",
- + .expected_cpu_id = 0x6348,
- +
- + .has_uart0 = 1,
- + .has_enet0 = 1,
- + .has_enet1 = 1,
- + .has_pci = 1,
- +
- + .enet0 = {
- + .has_phy = 1,
- + .use_internal_phy = 1,
- + },
- + .enet1 = {
- + .has_phy = 1,
- + .phy_id = 0,
- + .force_speed_100 = 1,
- + .force_duplex_full = 1,
- + },
- +};
- #endif /* CONFIG_BCM63XX_CPU_6348 */
-
- /*
- @@ -1048,6 +1069,7 @@ static const struct board_info __initcon
- &board_96348_D4PW,
- &board_spw500v,
- &board_96348sv,
- + &board_V2500V_BB,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
- @@ -1087,6 +1109,7 @@ static struct of_device_id const bcm963x
- { .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, },
- { .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, },
- { .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, },
- + { .compatible = "bt,v2500v-bb", .data = &board_V2500V_BB, },
- { .compatible = "d-link,dsl-2640b-b", .data = &board_96348_D4PW, },
- { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, },
- { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, },
- @@ -1146,6 +1169,22 @@ void __init board_bcm963xx_init(void)
- val &= MPI_CSBASE_BASE_MASK;
- }
- boot_addr = (u8 *)KSEG1ADDR(val);
- + pr_info("Boot address 0x%08x\n",(unsigned int)boot_addr);
- +
- + /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
- + /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
- + /* Loading firmware from the CFE Prompt always loads to Bank 0 */
- + /* Do an early check of CFE and then select bank 0 */
- +
- + if (boot_addr == (u8 *)0xbf800000) {
- + u8 *tmp_boot_addr = (u8*)0xbfc00000;
- +
- + bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
- + if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
- + pr_info("V2500V: nvram bank 0\n");
- + boot_addr = tmp_boot_addr;
- + }
- + }
-
- /* dump cfe version */
- cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
- --- a/arch/mips/bcm63xx/dev-flash.c
- +++ b/arch/mips/bcm63xx/dev-flash.c
- @@ -20,6 +20,7 @@
- #include <linux/spi/spi.h>
- #include <linux/spi/flash.h>
-
- +#include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
- #include <bcm63xx_dev_flash.h>
- #include <bcm63xx_dev_hsspi.h>
- @@ -234,6 +235,13 @@ int __init bcm63xx_flash_register(int nu
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- val &= MPI_CSBASE_BASE_MASK;
-
- + /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
- + /* Loading from CFE always uses Bank 0 */
- + if (!strcmp(board_get_name(), "V2500V_BB")) {
- + pr_info("V2500V: Start in Bank 0\n");
- + val = val + 0x400000; // Select Bank 0 start address
- + }
- +
- mtd_resources[0].start = val;
- mtd_resources[0].end = 0x1FFFFFFF;
- }
|
